Repair is a troublesome, costly and long-term business. In the process of work, they use various building and finishing materials, depending on the task at hand.
The most popular bathroom finishes are tiles. This material is used to decorate corridors, kitchens and living rooms. During installation, you cannot do without a special adhesive. Among the rich assortment, Ceresit CM 11 glue is in special demand.
About the brand
The products of the above brand are in demand due to a number of advantages and special qualities. Tile adhesive Ceresit CM 11 plus, intended for laying ceramic tiles, was highly appreciated by both professionals in the field of renovation and ordinary buyers looking for a golden value for money.
For the manufacture of products, the company uses carefully selected raw materials and innovative equipment.allowing to manufacture large volumes of goods without loss of quality. Products undergo control at all stages of production and receive a corresponding certificate. With the use of Ceresit adhesives, work will go smoothly and without problems.
The appearance of the finish, its strength and durability will depend on the choice of solution. A strong adhesive will hold the tiles in place, withstanding indoor climate conditions as well as external loads. Higher requirements are imposed on the compositions used on the basis of rooms in high humidity and dampness.
Product characteristics
The tile adhesive must have certain qualities and characteristics. Compositions from the German brand Ceresit have all the necessary functions.
CM11 product has the following properties:
- an environmentally friendly product, safe to use due to its special composition, while under the influence of high temperatures the glue does not emit harmful volatile elements;
- excellent indicator of frost resistance;
- the mortar is resistant to slipping, retaining its shape and strength from year to year;
- high adhesion to the surface;
- the composition demonstrates excellent moisture-repellent properties, which are required for adhesives used in bathrooms and other similar locations;
- the product is suitable for work both outside and inside buildings;
- Ceresit CM 11 can be used for installing large tiles, the size of which reaches 50x50 centimeters.
The technical parameters of the product make it in demand in the conditions of repair
- The product is diluted in water before use. For 25 kilograms, 6 liters of liquid will be needed (an approximate ratio of 1: 4).
- The ready-made solution can be used for 1.5-2 hours. After which it dries up, and the mixture cannot be applied.
- Air humidity indicator - 80%.
- The minimum temperature indicator for using the mixture is 5 degrees Celsius, the maximum is 30 degrees Celsius above zero.
- The "open" working time of the layer is 25 minutes.
- The maximum slippage of the tiles is no more than 0.5 millimeters.
- Consumption per 1m2 - from 1.7 to 4.2 kilograms.
- Complete drying takes 24 to 36 hours.
- The shelf life of the product in a whole package is one year.
Note: at the end of the installation process, it is necessary to grout the joints for an aesthetic finish.
Additional features
You can add CC83 elasticizer to the composition. This component will expand the scope of use. Proportions: 4 l CC 83, 25 kg mixture, 2 l water.
In this case, the mixture can be used for such work:
- installation of tiles for lining the pool and other open tanks;
- laying heated screeds;
- tight fixation of tiles with water absorption of more than 3%;
- tiling of basements, external stairs, parapets, terraces and other similar objects;
- cladding with mineral slabs;
- repair of entrance groups.
Scope of use
CM 11 Plus is specially designed for reliable and durable fixation of stone and ceramic slabs. However, they are not suitable for laying marble finishes; in this case, CM 115 glue is used.
Experts recommend using an adhesive when finishing horizontal and vertical substrates on non-deformable mineral surfaces:
- concrete surfaces;
- cement screeds;
- over cement-lime plaster;
- cement bases and others.
And also the product can be used to decorate brick surfaces. Due to its environmental friendliness, the product is recommended for indoor use.
If you use a mixture of Ceresit CM 11 together with various additives, you can prepare a reliable and practical building material for external use. The solution, prepared correctly, has a dense, non-deformable texture.
How to prepare the foundation?
Before starting repairs, it is necessary to properly prepare the base. Be sure to clean and dry the work surface. If necessary, various defects are eliminated, such as cracks, gouges, chips and much more. And also oil stains are removed from the base, grinding is carried out. Do not take preparation lightly. Otherwise, the result of the work will be unsatisfactory.
Check that the base is strong enough and has the required load-bearing capacity. If there are irregularities up to five millimeters on the surface, then they can be covered using the same adhesive composition. This must be done one day before the installation of the finishing material.
Preparing the adhesive mixture
To prepare the solution, the powder is diluted with ordinary water. You should use a liquid with a temperature of 15 to 25 degrees Celsius above zero. If necessary, use CC 83 modifier instead of water, diluted in a 2: 1 ratio.
Dry glue is added to the water gradually, constantly stirring the composition. The result should be a homogeneous liquid without lumps. Experts advise using a mixer or drill with an appropriate attachment. The optimum rotation speed is from 400 to 800 revolutions per second. After preparing the composition, it is necessary to pause for five minutes. During this time, the mixture will infuse, after which it must be thoroughly mixed again.
Apply adhesive
An ordinary smooth trowel is used to apply the adhesive. The comb structure is profiled with a serrated tool. Depending on the size of the finishing material, the size of the teeth is selected.
When working with large and heavy tiles, experts advise adding a thin layer of mortar to the mounting (back) side of the dies. And also professionals apply the adhesive to the tiles when performing repairs outside the building.
The finishing material, in this case the tile, does not need to be soaked. The dies must be pressed to the surface no later than 15-20 minutes after the glue has been applied to the wall. For 20-25 minutes, the position of the tiles can be adjusted without problems.
In no case should the tiles be installed end-to-end. It is imperative to arrange the joints. The width of the joints between the dies depends on such factors: the size of the tiles, the microclimate in the room, the operating conditions. For reliable grouting, use special grouting mixtures.
See below for more details.
Removing glue particles
To remove fresh residues of the composition, it is enough to rinse them with warm water. In the event that the glue has time to dry, a mechanical removal method is used. The optimum air temperature for finishing work varies from 5 to 30 degrees Celsius.
Quality assurance from the manufacturer
The Ceresit trademark provides customers with a quality guarantee for each unit of production. Manufacturers assure that the composition of Ceresit CM 11 fully complies with all the declared performance characteristics. In order to fully appreciate all the properties of the compositions of the above brand, it is imperative to follow the rules for storing goods, transporting, preparing and using.
It should be noted that representatives of the company are not responsible for the inappropriate use of mixtures. Before purchasing, each customer has the opportunity to familiarize himself with the composition of the product, the scope of use and technical characteristics.
What do you need to know?
Regardless of who is doing the work, a beginner or an experienced professional, it is imperative to adhere to safety precautions. First of all, you need to protect your eyes with special goggles. They can be purchased at any hardware store. Remember that the product contains cement, which reacts alkalinely with water.
If the composition gets on the skin, it must be immediately washed off with water and seek the help of a medical professional.
During finishing work outside the room, it is strongly recommended to use a combined tile laying method for a closer contact between the panels.
Testimonials
Consider the opinions of real buyers about the manufacturer's products. Given the popularity of products from the above brand, the network has collected a huge number of responses. After analyzing the thematic sites, it is safe to say that the Ceresit CM 11 adhesive is popular with Russian buyers. Most of the reviews are positive responses. Users note the excellent quality of products, reliability and excellent results.
Despite the many positive responses, there are also negative ones. Some consumers believe that there are enough analogs of mixtures on the market at a better price.