Tile Dismantling: How To Carefully Remove A Tile Product From A Drywall Wall, How To Remove Old Ceramic Tiles

Table of contents:

Tile Dismantling: How To Carefully Remove A Tile Product From A Drywall Wall, How To Remove Old Ceramic Tiles
Tile Dismantling: How To Carefully Remove A Tile Product From A Drywall Wall, How To Remove Old Ceramic Tiles

Video: Tile Dismantling: How To Carefully Remove A Tile Product From A Drywall Wall, How To Remove Old Ceramic Tiles

Отличия серверных жестких дисков от десктопных
Video: How to Remove Tiles from Bathroom Wall | DIY Part 1 2023, January
Anonim

Even redecorating almost always involves removing the old finish as a first step. If in the case of wallpaper on the walls and linoleum on the floor, this procedure does not seem so difficult, then the tile can become a serious obstacle, significantly complicating the implementation of the task.

At the same time, mankind is unlikely to give up tiles as a material for finishing literally everything - floors, walls and ceilings, because its service life exceeds all expectations, and even the high cost does not stop consumers from buying it. However, even tiles sometimes require replacement, so it's worth figuring out how to organize the removal process.

Image
Image
Image
Image
Image
Image

Features of the

The tile removal technology strongly depends on the end result the consumer needs. If the tile is rather worn out and is unlikely to be suitable for something else, then there are no special requirements for the accuracy of dismantling - the wall under the masonry will still not remain even, if you don't try here. Another thing is that sometimes the owners see the point in preserving the old tile, if it looks pretty good. In such a situation, it can be reused, provided that a significant number of slabs remain intact.

This is not to say that using old tiles will allow you to make an amazing renovation in another place, but for a summer cottage or garage, such a solution will be very practical.

Image
Image
Image
Image

At the same time, there are such types of masonry that you simply cannot remove accurately - “thank you” for this must be said to the master who laid the tiles so that she could serve her owner as long as possible. For this reason, it follows before starting removal, gently tap the tiles in different places with a hammer with a rubber nozzle.

The large number of voids found under the surface of the tile indicates the use of tile adhesive or not the best quality cement masonry. In this case, you can try to keep the removed trim. However, you should not immediately stock up on boundless optimism, because on average, losses amount to up to half of the entire tile.

Image
Image
Image
Image

If there are no voids, it is likely that the laying was carried out on a cement-sand mortar, and even carefully, which practically negates the hope of reusing the tile. Good cement is not afraid of moisture and is able to functionally serve for decades, and when it nevertheless loses its strength, then the ceramics itself can hardly boast of reliability.

It should be noted that tile glue began to be actively used only in the last couple of decades, and before that the masters were limited almost exclusively to cement. This means that you should not even try to disassemble the old masonry without tapped voids, because the amount of losses will approach 100%.

Image
Image
Image
Image

Methods

The tile removal technique is divided into two types - neat and sloppy methods. It's worth starting with the latter, because they require less skill and can be produced in no time.

It is possible to remove the tile in an inaccurate way on your own, because it does not imply any rules, except for strict adherence to safety precautions… Nevertheless, such dismantling will probably require brute force - you will have to hold at least a working puncher in your hands or knock down the tiles by hand using a hammer and chisel.

Naturally, the first option is somewhat more practical - it will not be possible to avoid the terrible noise with it, however, the battle will be carried out without much effort and in the shortest possible time. Manual knocking down should be left only for those cases when the owner does not have a perforator and there is nowhere to borrow it, because such a procedure is much more tiring, and it will take a lot of time, although the result will be the same.

Image
Image
Image
Image

It should be understood that the dismantling of the tiles in any case presupposes the presence of protective ammunition, and if the interior is renewed also by a rough method, then a full-fledged suit is simply necessary.

It assumes maximum coverage of the entire body surface, including thick shoes, heavy gloves, goggles and a respirator. Even the correct direction of impact on each tile cannot guarantee that a breakaway piece of tile or mortar will not hit the master with a sharp end, and building dust is an integral attribute when performing such work.

Image
Image

As for neat removal, its technique varies much more - the choice of specific means depends on several factors, including the position of the tile (on the walls, floor or ceiling), its size and thickness, as well as the base on which it was once planted (solution or glue).

Image
Image
Image
Image

How to shoot?

Professional repairmen have everything they need, but a person who decides to do home repairs on their own will need advice on the tools needed in the process.

When preparing for the start of work, it is advisable to have at your disposal, if not the entire list, then at least most of these things:

  • Hammer… Not everyone has a hammer at home, but every self-respecting man probably has a hammer. This tool is useful for both rough and neat tile removal, therefore it can be called irreplaceable. If there are several hammers, it is better to choose a conditional average - both in size and weight.
  • Chisel or impact screwdriver… Since the main emphasis is on doing the work by hand, then the set with the hammer must have a tool that must be hit with this very hammer in order to pry out each individual tile.

As practice shows, the wider the choice of such tools, the more opportunities for neat tile removal.

Image
Image
  • Perforator… First of all, it is necessary for those who do not seek to keep the tiles intact, but even thrifty owners will need it if the masonry sits too firmly in certain places. Such a tool should be equipped with various special attachments - chisels and bits, pikes and drills.
  • Construction knives and narrow strong trowels… These tools will greatly simplify the process of neat tile removal, since they can crawl under each individual tile if the mortar holding it has already partially crumbled.
  • Chisel or grinder with a special attachment… For rough removal of the old finish, such devices are not needed, but for the reuse of the removed tiles, they are simply necessary. Such tools contribute to the accurate removal of grout, which just interferes with picking up the tiles in the right place.
Image
Image
Image
Image

Algorithm of work

You can dismantle an old tile with your own hands in different ways, but the choice of a specific method depends on the location of the tile and the method of fixing it.

Most often, it is necessary to remove the old tiles from the wall without regard to its subsequent preservation. For this you must first secure communications - turn off the electrical wiring in this room, and also protect all pipes in the room with a thick layer of soft rags.Removal of tiled wall tiles most often occurs where they are laid - in rooms with high humidity, and there are always such communications such as water supply, sewerage, heated towel railall of them must be properly protected… If the removal of the granite tiles from the floor is not yet planned, it must also be covered.

Image
Image
Image
Image

Regardless of which toolkit you plan to use, you need to start from one of the corners of the top row… If you start at the bottom, there is always a risk that a huge piece of several connected pieces will fall right on your feet, while starting at the top allows you to hit no more than one piece of tile at a time. At the same time, it is not recommended to regret the first tile - it is unlikely that it will be possible to remove it neatly, so you can safely break it.

Further, removal occurs either with a perforator or with a hammer and chisel; in the second case, you can tear off the tile more accurately, but this method is little used. If the installation was carried out efficiently, then you can only peel off the tile planted with glue.

Image
Image
Image
Image

In case of minor damage to ceramic tiles on the walls, you can replace only one or a few parts instead of a full replacement of the masonry. In this case recommend to remove grout chisel and carefully pick out the desired fragment of the tile with a chisel, trying to achieve delamination.

If this does not work, you will have to carefully break the desired tile and remove it piece by piece. However, when using a high-quality solution, even this may not help - then all that remains is to cut the tile diagonally in a cross with a cutter, and then drill small holes along the lines with a drill. In this case, the tile will fall off in pieces if you gently tap it with a hammer.

Image
Image
Image
Image

Removing the cladding tiles from the drywall wall is a huge problem, because even a relatively neat hammer and chisel can break the drywall surface. As a rule, tiles are more likely to be removed from such a wall intact and neat, but the wall itself cannot be preserved..

It remains only to remove the tiles as carefully as possible with a hammer and a chisel with the obligatory preliminary cleaning of the tile joints, and in those places where the integrity of the wall will be violated, carry out minor repairs in the form of overlaying a new sheet of drywall. Such a fragment is fixed with self-tapping screws, and the gaps are sealed with a special putty.

Image
Image
Image
Image

The tiles on the floor can be attached not only to the concrete screed, but even to the previous floor. First, the workspace needs to be cleaned of both furniture and dirt, and then tap the tiles to determine the presence and location of voids.

The hammer drill will solve the problem quickly, but it will require the obligatory leveling of the floor., a neat method involves breaking the corner slab and then prying the neighboring ones with a chisel. To achieve increased accuracy of the procedure, it is recommended to first wet the seams with water and remove the grout, and only then remove the tile itself.

In some cases, well-laid quartz vinyl tiles can be so difficult to remove that it is more practical to install the new coating directly on top of the old one, provided that it remains reliable.

Image
Image
Image
Image

For finishing ceilings, usually not tiled, but foam tiles are used, but it cannot be said that this simplifies the task of removing it from the ceiling - the low weight contributes to the reliable adhesion of the coating to the surface, which makes it almost impossible to remove the finish in whole fragments. If you try to remove the ceiling tiles with your bare hands, you will only get a huge amount of foam crumbs.so it is recommended to try removing it with a spatula.

It is noted that a large amount of used glue actually excludes a method of removal with a spatula, therefore chisel and hammer will come in handy here too. Remaining glue on the ceiling is removed with a solvent or it is preheated with an industrial hair dryer and then scraped off with the same spatula.

In some cases, when high-quality thick tiles and good expensive glue were used for them, the most practical would be to refuse to remove the finish and install a stretch ceiling.

Image
Image
Image
Image

For information on how to dismantle the tiles, see the next video.

Tips & Tricks

Finally, a few more tips should be given that will make the dismantling of the tile quick and practical:

Consider possible tile removal methods long before starting work. To do this, you should decide whether the old tile is needed for further use and whether it can be removed at all without damage. It should be noted that when using a cement-sand mortar, even a completely broken tile is unlikely to be useful for subsequent re-installation. It will definitely have cement protrusions on the back side, and it will simply not work to align it after removal, without splitting or breaking

Image
Image
  • In all instructions, it is recommended to protect all fragile surfaces, including pipes and even plumbing, with thick rags, but it should be borne in mind that large and sharp pieces of tiles can damage even the paint on the walls. This is especially true for oil paint, as well as other types of dyes that form a dense, highly visible layer. Sometimes you should choose a neat method of dismantling, not so much to preserve the old tiles, but simply to avoid the need to rebuild the entire room.
  • The risk of injury during tile dismantling is very high - any professional in this field will confirm this. In no case should the instructions be disregarded, in particular the use of a full protective suit is strictly mandatory and no details of it can be excluded; if they are not there, it is better to buy them than to be treated later.

Popular by topic