I Washed Down The Tiles At 45 Degrees: How To Cut At An Angle With Your Own Hands, Cutting, Trimming And Laying Ceramic Products

Repairs 2023

Table of contents:

I Washed Down The Tiles At 45 Degrees: How To Cut At An Angle With Your Own Hands, Cutting, Trimming And Laying Ceramic Products
I Washed Down The Tiles At 45 Degrees: How To Cut At An Angle With Your Own Hands, Cutting, Trimming And Laying Ceramic Products
Video: I Washed Down The Tiles At 45 Degrees: How To Cut At An Angle With Your Own Hands, Cutting, Trimming And Laying Ceramic Products
Video: Dry tile cut at 45 degree. Сухая резка края плитки под 45 градусов. 2023, February
Anonim

The presence of corners or bulges on the wall, different ways of laying tiles, as well as non-standard room dimensions play a huge role in the cladding workflow, causing additional difficulties. Therefore, you often have to deal with the need to grind tiles.

Outside straight corners, which are filed at 45 degrees, form a neat right angle with a smooth transition, so there is no need to resort to the use of overhead aluminum or plastic corners. However, in order for the cuts to be accurate and in line with other parts of the tile, special tools must be used.

Image
Image
Image
Image

What is it for?

Basically, the corner edge of the tile is washed down at 45 degrees in the following cases:

  • to match the inner and outer corners of a rectangular tile when they are joined during laying;
  • to form a beautiful beveled edge;
  • with a diagonal tile layout.
Image
Image
Image
Image
Image
Image

Trimming the edge part of tile products at a special angular slope makes it possible to forget about the use of overhead corners forever.

Tools

It is possible to make a high-quality and even cut without chips and cracks only with the help of special devices, each of which has its own advantages.

Electric machine

The main advantage of this tile cutter is a clear and high-quality cut on the tile, which is carried out in two directions: an ordinary straight cut and a special cut at an angle of 45 degrees. Thanks to the turning of the cut-off wheel at a certain angle to the cut-off part of the tile, it is easy to make a cut, starting from 0 to 45 degrees. The electric machine can have a water supply function, due to which less dust is emitted, or it can have a conventional design. However, both versions of the devices provide the same quality of work and guarantee a large volume of tiles was washed down in a short time.

Image
Image
Image
Image

When cutting tiles with concave shapes, the electric tile cutter does not repeat the concave deflection of the product. Therefore, you can only cut off the back side so as not to touch the enamel on the front side. This is especially true for porcelain stoneware.

Necessary accessories:

  • special masking tape;
  • simple pencil;
  • small ruler;
  • tile cutter;
  • grinder with adjustable speed revs.
Image
Image
Image
Image
Image
Image
Image
Image

On the part of the tile where the cut will take place, you need to stick masking tape. Make the necessary markings with a pencil and a ruler. Then place the tile on a specific area of ​​the device at a 45 degree angle. On the principle of a circular saw, tiles are cut with a diamond band. In some models, water is supplied during the cut, which protects the tiles from melting and washes away dust.

In case of damage to the glaze of the outer part of the tile, the saw cut will turn out to be ugly with the presence of cracks and chipped edges, which, when laid to each other, will have a sloppy appearance. Therefore, when working with an electric tile cutter, you need to carefully remove only the clay layer.

Image
Image

Professional Secrets of Experienced Tilers:

  • using a tile cutter, it is necessary to achieve an even cut;
  • then form the required angle on the back of the product;
  • glaze, which was touched in the working process, is rubbed with sandpaper.
Image
Image
Image
Image

Manual tile cutter

The manual tile cutter is popular not only among professional tilers, but also among hobbyists.Many models of such tile cutters are equipped with a special rotary base and a built-in ruler, which allow you to make a high-quality cut of tiles at 45 degrees. After inserting the tile into the tile cutter at a certain degree, it is necessary to align the mark on the tile and on the construction tool. Having lowered the handle down, you need to move it away from you with slow movements at the same speed and even pressing.

Image
Image

Bulgarian

Despite the fact that such a building device is present in almost every home, it is very difficult to cut the tiles yourself at a 45-degree angle with a grinder.

For a quick and even cut of the tile, it is necessary to install a diamond wheel on the device. In this case, the tile should be placed under the rib with the outside to the bottom. Now the grinder needs to grind off the back of the ceramic tile at an angle of 45 degrees.

From the first time, it will not work to make an even and clean cut. Therefore, after the corner has been formed, it is necessary to repeat the process and walk the grinder's diamond circle along the cut edge. Only in this way will the angle become even.

Image
Image
Image
Image

To form a corner on the tile, it is necessary to choose the right grinder, since not all models can perform the necessary functions. In this case, it is worth purchasing a construction tool from which you can adjust the speed.

At the beginning of work, you should set the minimum speed at which the edges of the tile will be sanded, and not burned.

Image
Image

Basic Rules

When grouting tiles, it must be remembered that only clay can be cut, not reaching the glaze 0.5-1 mm. In this case, the corner of the tile will turn out to be nice and smooth, without damage or chipping.

Modern capabilities and the skill of specialists allow you to cut tiles at 45 degrees not only from the edge, but also in the middle of the product. To do this, the tiles must be measured and cut in accordance with the required size, and then cut at 45 degrees. To get a high-quality result, you should seal the cut edge with sandpaper.

Image
Image
Image
Image

How to form an acute angle correctly?

The next step after the process of cutting the tiles to a degree of a certain angle is its worthy use, as well as the organization of a right angle. To do this, the following points must be observed:

  • using a special building level, it is necessary to evenly glue the first part of the tile. Its trimmed edge should slightly protrude beyond the base of the right angle;
  • the second tile should be glued on the opposite side in the same way, the fixing period of the glue at the same time allows you to move and adjust the touching tiles in order to achieve a tight contact.
Image
Image
Image
Image

Before you start facing the corner, you should check the vertical consistency of the wall. Even with the lowest elevation differences, the angle at the top may not converge and turn out to be even. It will be impossible to disguise or patch up this flaw in the future.

The scope of use of a sawn-off tile at an angle of forty-five degrees has certain limitations. As a result of the cut clay on the back side, the narrowed edges of the tile become thin and brittle, so they can easily break off.

Image
Image
Image
Image

It is not recommended to form right angles from cut tiles in places where there is heavy traffic.

Slicing without special tools

It is not necessary to grind the tile using special devices. At home, you can easily hand-wash the tiles at 45 degrees. To do this, proceed as follows:

  • on the outer part of the tile (glaze), a line is drawn with a glass cutter;
  • with the help of a grinder, a small groove in the form of an English letter "V" is formed on the back of the tile, which is positioned along the width of the entire tile;
  • then you need to gently break the bend of the cut and sand it with sandpaper.
Image
Image

How to make a mosaic cut?

Today, many modern designers use mosaics when decorating rooms - small ceramic tiles that are no different from ordinary tiles, except for their size. Therefore, often when using this tile, it also becomes necessary to cut it at an angle of 45 degrees.

To wash down small tiles, it will be most convenient to use an electric tile cutter, in which it is necessary to place movable small pieces of the mosaic with the glaze down. Having conveniently fixed them on the back of the cutting disc, you can start the sawing process while holding the tiles with your hand. The same as for burring of ordinary ceramic tiles, when cutting down the mosaic, remember about the outer layer of glaze, which is not recommended to reach.

Image
Image

An equally complicated process was washing down the mosaic with an ordinary grinder, which is accompanied by a lot of dust. In this case, the tiles should also be fixed with the outside facing down. Only during work is it necessary to find a suitable object and hold on to small pieces of tiles that are constantly moving.

The work of the grinder should be at the lowest speed. With slow movements, it is necessary to remove the back layer of clay using a diamond wheel. However, it is not possible to carefully saw down the cut edge of the tile with a grinder, therefore, upon completion of the process, it is necessary to seal it with sandpaper.

Pruning and filing should ideally be done by a professional.

Image
Image

Today, the use of aluminum or plastic corners has decreased due to the ability to wash down the tiles at 45 degrees. This method, like joining tiles at a right angle, has been known for a long time. Previously, such methods were used in the facing work of the facades of various buildings. Now, such options for laying ceramic tiles can be found in almost every home.

However, with all the positive characteristics of washing down the tiles, this process also has negative sides. This corner of the tile becomes too thin and vulnerable, so it can easily crumble, which will lead to unnecessary trouble and waste.

To learn how to cut the end of the mosaic at 45 degrees, see below.

Popular by topic