Water Is Not Collected In The Toilet Cistern: What To Do? Why Does It Go Badly Into The Bottom-lined Tank? How To Fix A Waste Cistern?

Table of contents:

Water Is Not Collected In The Toilet Cistern: What To Do? Why Does It Go Badly Into The Bottom-lined Tank? How To Fix A Waste Cistern?
Water Is Not Collected In The Toilet Cistern: What To Do? Why Does It Go Badly Into The Bottom-lined Tank? How To Fix A Waste Cistern?

Video: Water Is Not Collected In The Toilet Cistern: What To Do? Why Does It Go Badly Into The Bottom-lined Tank? How To Fix A Waste Cistern?

Отличия серверных жестких дисков от десктопных
Video: Toilet Tank Not Filling Up With Water 2023, January
Anonim

Over time, malfunctions occur in the functioning of any plumbing fixtures, even if they are installed correctly. One of the most common toilet breakdowns is a malfunction associated with the fact that the liquid is not poured into the cistern at all, or it takes too long. Of course, it is best to contact the master when such a breakdown occurs, but if you wish, you can correct the situation on your own.

Image
Image
Image
Image

Malfunctions and their causes

If water stops flowing into the toilet cistern, then you need to pay special attention to such a malfunction and try to fix the breakdown as quickly as possible, otherwise the toilet bowl may completely fail, in which case you will need to change the entire structure. In order not to spend extra money for plumbing services and not buy new equipment, you can try to cope with the breakdown yourself. However, first you need to find out for what reason it happened.

Do not immediately rush and disassemble the device, first, make sure that there is water in the plumbing system of the apartment or house. According to experts, about 40% of all water drainage faults occur due to the fact that water does not enter the structure itself.

That is why you first need to clarify whether there is cold water supply in the house, and only after that you can start looking for the reasons that led to the malfunction.

Image
Image
Image
Image

If the system is completely full and there is a sufficient volume of water in it, but the device is inoperative, this may indicate the presence of another type of breakdown. These include the following types of malfunctions.

  1. The float is in the wrong position… This nuisance often causes the toilet tank to not fill. Also, breakage can cause leakage, which further exacerbates the situation. Such a malfunction must be excluded in the first place, since the float tends to pass or completely block the liquid, being in different positions.
  2. Water supply hose damaged or clogged… Such breakdowns cause too slow flow of fluid from the system, and sometimes completely block it. Often, there are cases when rust particles or sand are collected in the place where the toilet pipe is connected to the plumbing device or in its filter. This circumstance also often becomes an explanation for the fact that the liquid is drawn into the reservoir for too long or does not go at all. Most often, such blockages occur after the repair of utilities.
  3. There is a breakage, blockage or other damage to the exhaust valve… This happens when the fasteners are too tightly tightened - nuts, bolts and other structural parts. You should inspect all the joints as carefully as possible, make sure that everything is assembled securely, but at the same time not overtightened.
Image
Image
Image
Image
Image
Image

Make sure there is no mucus and plaque on any toilet components, since their presence most often ends with the failure of the structure.

Image
Image

What to do?

If the owner of the living space decided to independently deal with the source of the problem and fix the problem, then he will have to make some effort. Moreover, there is no guarantee that the attempt to repair the equipment will necessarily be successful.

However, you can always try to make small repairs and save money.

Image
Image

Float misalignment repair

If the toilet flush cistern is broken and does not collect water in the required volume, then, most likely, the reason for this is related with a skewed float. In this situation, it is necessary to open the container lid - a mechanism is located in the liquid, as well as a lever, at the opposite end of which a small displacer is fixed - that is, a float. It is this structural detail that is responsible for taking water to the required volume, after which it closes the inlet valve.

If a misalignment occurs, the valve stops the fluid supply prematurely, and this ends with the failure of the mechanism. To eliminate the breakdown, you need to quickly and accurately set the buoy to its original position. - after that, the system performance should be fully restored.

Image
Image
Image
Image

When the water supply valve is clogged

If water does not go into the toilet cistern, despite the fact that it is present in the water supply system, then it is possible that the cause of such a malfunction was the intake valve is clogged due to sand, debris, rust and other contaminants.

First you need to disconnect the liquid leash to the toilet tank. As a rule, in apartments and private houses there is a single tap that can completely shut off all the water - it is this that needs to be turned on. Then the underwater hose attached to the tank is disconnected, scrolled, twisted and removed.

It is necessary to work with all caution, since sediment from the water supply system can lead to big trouble if the hose is carelessly disconnected.

Image
Image
Image
Image

Next, an external examination is carried out in order to detect the area where the blockage has accumulated, then it is carefully cleaned with a thin flexible wire. At the end, the supply valve is released a little so that the residual dirt and coarse debris are washed out under the action of the water pressure.

After you remove the blockage, all that remains is to carefully perform all the steps in reverse order. At the end of the work, check the water intake level and, if necessary, adjust it through the bend of the lever and changes in the position of the buoy.

As you know, any problem is easier to prevent than to solve. Was no exception plumbing breakdown - in order to minimize the occurrence of blockages, it is necessary to regularly clean and rinse the drainage mechanism. Timely prophylaxis will ensure that you will not have an unpleasant situation in which the toilet bowl cannot collect liquid into the tank.

Image
Image
Image
Image

If the supply hose is damaged

When figuring out the reasons why the toilet does not collect water, by all means you need to check the underwater hose through which the liquid goes to this tank. This is one of the most common breakdowns that homeowners complain about.

Some time after the purchase, the materials used for the production of plumbing fixtures and their components wear out and fail - then such troubles as the lack of water in the drain tank cannot be avoided.

Image
Image
Image
Image

The hose is changed according to the following algorithm

  1. Depending on the structural and technological features of the water supply system in the house, the common water supply tap is closed.
  2. After that, the inlet hose is unscrewed and carefully examined. If during the inspection you find cracks or holes, as well as other deformations, then the hose will have to be replaced. Otherwise, you will not be able to solve the problem of the lack of water flow into the toilet cistern.
  3. If there are no defects visible to the eye on the hose, it must be lowered into a previously prepared container and the common tap slightly opened. As a result of such actions, you will notice areas of leakage, as water will appear in them. The defective underwater hose must be replaced with a new one and continue to use the plumbing fixture.
Image
Image
Image
Image

When there is a blockage in the drain

A lot of problems for the owners of residential premises are created by clogging of the drain, from which the liquid enters the toilet. It should be noted that this has no effect on the water intake, it continues to flow into the tank and raises the float to the required level, but the drain mechanism does not work at the same time.

The problem is resolved as follows

To begin with, raise the lid and unscrew the drain button, after which they carefully examine the lower part of the exhaust valve - when the trigger is pressed, it should open.

Image
Image
Image
Image

If any dirt is found, it is removed mechanically, usually with your fingers. If you do not see any debris, then the cause of the malfunction may be in the pipe connecting the tank to the water supply. This breakage is usually caused by plaque and mucus on the inner surfaces of the device.

For cleaning in this case it is best to use household chemicals, for example, such a tool as "Mole". But remember that it must be used with extreme caution, because it contains caustic substances that can harm the skin and mucous membranes of the human respiratory system.

Image
Image
Image
Image

Recommendations

There are some other situations that lead to the fact that no liquid enters the toilet cistern. For example, sometimes, when installing plumbing, parts twist together too much, and for this reason they cease to correctly perform their main functions. With a similar problem, all structural elements must be disassembled, cleaned and installed back.

A common reason that water is drawn too poorly into the toilet bowl is drop in head pressure. This is often the result of other appliances, such as a washing machine, dishwasher or shower.

In this case, a specialized regulator will help to cope with the problem - it is installed in houses in order to prevent pressure loss if several devices work at the same time.

Image
Image
Image
Image

If the liquid is not collected in the newly installed tank, then most likely there is manufacturing defects… To solve such a problem, you need to contact the store where you made the purchase - usually in such cases they make free repairs or replace the equipment with new ones.

Professional plumbers recommend taking preventive measures at least 2 times a year - thus, you can keep the device in working order for a long time. This will minimize the likelihood of problems associated with drawing water from the toilet.

In the event of such a malfunction, repairs must be carried out promptly., since the problem will not be resolved by itself, and over time it will only get worse. The consequence can be flooding of the toilet and neighbors, and if the underwater valve assembly is clogged, the hose may even burst under pressure. As a result, you will need to replace the cistern, the toilet bowl, and the entire liner - this will entail considerable financial costs.

Image
Image

If you could not fix the plumbing yourself, and the water still does not run, and the tank, despite the repair, does not fill, contact the specialists - they have all the skills and tools needed to work.

For information on why water is not collected in the toilet cistern, see the next video.

Popular by topic